How To Install The Surface Mounted Downlight ?

  • By:Ronse
  • Date:2021/10/14

Step: Measure the Lights

To understand what holes you require to make to install the downlights, you need to measure their rear diameter. Put the light down and utilize a measuring tape to examine the size of the part that will be installed inside your ceiling. Bear in mind not to determine the cut side of the light. Otherwise, your holes will be too huge to fit the downlights. If you still have the product packaging, you can also just examine the details placed there.

 

Action: Locate the Piping and Wiring

Apart from the joists, you ought to locate the piping and circuitry in your ceiling not to hurt them. When you choose a place to install a led recessed downlight, first move a wire and pipeline detector backward and forward over the surface area and examine if the tool alerts you in any way. If not, mark the area with a pencil. If you can refrain from doing it by yourself, ask a home plumbing professional, electrical expert, or inspector to do that for you.

 

Step: Prepare the Lights to be Mounted

Keep the spring clips against the light's sides. Keep in mind that your downlights are provided with spring-loaded metal clips snapping open while being released. Take those spring clips below and move them as much as make them lie flush with the light's base. Continue to hold them down to ensure they do not snap open throughout the installation. If you are dealing with a surface mounted downlight, there will be no spring clips, and you will just need to press and snap it to the installing plate that you previously attached.

 

Step: Strip the Wires

Both wires on the recessed light and the wall need to be stripped at the ends. The wire stripper and clamp need to be opened the last 1/2 inch of the 14/2 wire between the jaws. Then, you should pull wire strippers towards the end cable television so that the insulation can be removed. When you are completed, do the same to the cable connected to the recessed light. You will find red or black, white, and uninsulated wires.

   

The most substantial thing to keep in mind when you will wire something or do any other repairs or upgrades of this kind is to go to the electrical control box in your home and switch off the power. To examine if there is no voltage for sure, it is suggested to test the outlets and wires with a wire tester.

 

Step: Get Rid of the Cut Ceiling Piece

Take the saw out through the hole when you break through the other side. For safety reasons, turn off your drill completely. Then, put the end of a screwdriver between the saw's side and the fragment of your ceiling that landed inside it. Pry that piece out of the blade and get rid of it.

 

Congratulations! You have just mounted the very first downlight at your house. Bring the voltage back and enjoy your brand-new lighting when you are finished with all of them!

 

Action: Install the Wire

There are 2 alternatives-- either to link the downlights to a switch you already have or to broaden the circuit with a brand-new one. Use a wire tape to feed a 14/2 cable through the wall in such a way that it lines up with the area where you want to install the light. In the 14/2 cable television, there is one neutral wire, one ground, and one hot. If you currently have a junction box, it is also a great idea to set up a downlight there, after getting rid of the existing lighting function.

 

Action: Search for the Joists

You need to know where the joists are in it if you want to install downlights in your ceiling. A stud finder will surely show beneficial for this job! You simply need to turn it on and keep it flat versus the surface area you wish to search. When you see it lighting up or hear it beeping, move the tool slowly on the ceiling up to the point. To know where the edge of a joist was found, mark this area with a pencil. Do it all across the surface to be aware of which locations you must omit while setting up the lights.

 

Action: Put the Light in the Hole

Place the light in the hole and push slightly approximately the moment you hear the clips snapping. Inspect if all the wires are put in the hole before the downlight, and keep pushing the light into the ceiling so that the clips can be inserted in the hole. After a clicking and snapping noise, delicately lower the light pull back to check if the spring clips handle to support it completely. Do not let go of the recessed light too quickly because if the clips do not work properly, they can fall out and break.

  

You can merely knock on the ceiling to check if it results in a hollow sound if you do not have a stud finder. If an echoing sound can be heard, it implies there is no joist behind it. Nevertheless, in the case of a strong thumping sound, the likelihood of hitting a joist is high.

Step: Splice the Wires

The matching wires ought to be accompanied by special wire caps. To do that, take 2 ends of the black wires together, pointing straight up. Then, utilize your pliers to twist the ends in such a way they could be spliced effectively. Take a wire cap and twist it clockwise onto the connection, and the exposed end will get a safe cover. Do the very same for white and uninsulated wires. Your lights might have connection boxes. If that is the case, line up the wires from the 14/2 cable to place them across the matching wires in the box. To make it all steady, tighten the screws.

  

Action: Drill the Holes with a Hole Saw

Cut the holes for the lights in your ceiling with the hole saw. Keep the blade perpendicular to the ceiling and make certain that the middle bit fits the mark you have made with your pencil before. Start the drill, and apply simply a little pressure so that the middle bit can enter into the ceiling. Keep in mind that the saw blade must stay flat in order not to cut the hole crooked. Deal with just short bursts as much as the moment you feel the blade pop out from the opposite. To protect from plaster or drywall falling on your face, do not forget to put on a dust mask and shatterproof glass.

 

Action: Prepare a Hole Saw

Supply your drill with a hole saw of the very same size as the eliminated you have determined. This accessory has a ring-shaped blade that can be joined with the end of your drill. If you have a selection of blades, pick the one enriched with carbide or diamond grits to attain the cleanest holes. Rotate the chuck counterclockwise to loosen it, and mount the hole saw onto it in such a way so that the blades can face out. To secure it, turn the chuck clockwise this time.

 

You might question, though, if it is required to call an expert electrician after buying them. In our viewpoint, if you have at least some standard DIY abilities and helpful tools, you ought to be able to install recessed lighting on your own. To assist you with that, we have prepared a thorough guide describing the whole process step by step. Let's do this!

 

Action: Mark the Spots for the Lights

When you already know where not to set up downlights, you require to choose the areas where you in fact will install them. Mark ideal places in between the joists-- it is best to draw a dot where you want the center of the light to be placed. Keep in mind to keep around 3-4 inches on either side of the dot to correctly fit the downlight in your ceiling.

 

Downlights (likewise called recessed lights) are getting growing popularity nowadays, mainly due to their stylish and stylish appearance. They have a unique style because they are not supposed to look as attached to the ceiling, but rather as an important part of it. They are particularly beneficial if you want to brighten an interior with a low ceiling because, in this way, you can provide appropriate lighting without disturbing your taller relatives or good friends. Downlights perfectly integrate both useful and decorative benefits, so they are highly valued in the lighting market. Most commonly, you can find them with LED bulbs inside.

 

Step: Space the Additional Lights

While including additional lights, remember that they need to be spaced 4-5 ft apart. Mark all the areas where your downlights will be set up. If they are properly distanced from each other, they will offer your interior with a proper light quantity without making it too intense at the same time.

INQUIRY

CONTACT US

contact-email
contact-logo

Foshan Ronse Lighting Technology Co., Ltd.

We are always providing our customers with reliable products and considerate services.

If you would like to keep touch with us directly, please go to contact us

  • Home

    Home

  • Tel

    Tel

  • Email

    Email

  • Contact

    Contact